STANDARDS

DIN EN ISO 4628-1: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 1: General introduction and evaluation system
DIN EN ISO 4628-2: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 2: Assessment of the degree of blistering
DIN EN ISO 4628-3: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 3: Evaluation of the degree of rust
DIN EN ISO 4628-4: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 4: Assessment of the degree of cracking
DIN EN ISO 4628-5: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 5: Evaluation of the degree of flaking
DIN EN ISO 4628-6: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 6: Assessment of the degree of chalking after the tape process
DIN EN ISO 4628-7: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 7: Assessment of the degree of chalking after the velvet process
DIN EN ISO 4628-8: Paints and varnishes - Assessment of coating damage - Evaluation of the amount and magnitude of damage and the intensity of uniform changes in appearance - Part 8: Assessment of delamination and corrosion from a scratch or other artificial lesion
AWN 060501: Purity requirements for hydraulic components and systems
DIN EN ISO 2360: Non-conductive coatings on non-magnetic metallic base materials - Measurement of layer thickness - Eddy current method
DIN EN ISO 2409: Paints and varnishes - Cross-cut test
DIN EN ISO 2808: Paints and varnishes - Determination of layer thickness
DIN EN ISO 2812-1: Paints and varnishes - Determination of resistance to liquids - Part 1: Immersion in liquids other than water
DIN EN ISO 2812-2: Paints and varnishes - Determination of resistance to liquids - Part 2: Procedure with immersion in water
DIN EN ISO 2812-3: Paints and varnishes - Determination of resistance to liquids - Part 3: Procedure with an absorbent material
DIN EN ISO 2812-4: Part 4: Drip / stain proceduresCoating materials - Determination of resistance to liquids - Part 4: Drip / stain method
DIN EN ISO 2812-5: Paints and varnishes - Determination of resistance to liquids - Part 5: Graded furnace method
DIN EN ISO 2813: Paints and varnishes - Determination of gloss value below 20 , 60 and 85
DIN EN ISO 6270-1: Paints and varnishes - Determination of resistance to moisture - Part 1: Condensation (one-sided stress)
DIN EN ISO 6270-2: Paints and varnishes - Determination of resistance to moisture - Part 2: Condensation (exposure in a climatic chamber with heated water tank)
DIN EN ISO 6272-1: Paints and varnishes - Determination of resistance to sudden deformation (impact test) - Part 1: Test for falling weight, large test surface
DIN EN ISO 6272-2: Paints and varnishes - Determination of resistance to sudden deformation (impact resistance) - Part 2: Test for falling weight, small test area
DIN EN ISO 6860: Paints and varnishes - mandrel bending test (with conical mandrel)
DIN EN ISO 9227: Corrosion tests in artificial atmospheres - salt spray tests
DIN EN ISO 15184: Paints and varnishes - Determination of hardness of coatings by testing with pencils
DIN EN ISO 20567-1: Paints and varnishes - Testing of stone chip resistance of coatings - Part 1: Multi-layer test
VDA-19: Technical cleanliness test - particle contamination of functionally relevant automotive parts
ISO 4406: Hydraulic fluid power - Fluids - Method for coding the level of contamination by solid particles
ISO 16232-1: Road vehicles - Part 1: Vocabulary
ISO 16232-2: Road vehicles - Cleanliness of components of fluid circuits - Part 2: Method of extraction of contaminants by agitation
ISO 16232-3: Road vehicles - Cleanliness of components of fluid circuits - Part 3: Method of extraction of contaminants by pressure rinsing
ISO 16232-4: Road vehicles - Cleanliness of components of fluid circuits - Part 4: Method of extraction of contaminants by ultrasonic techniques
ISO 16232-5: Road vehicles - Cleanliness of components of fluid circuits - Part 5: Method of extraction of contaminants on functional test bench
ISO 16232-6: Road vehicles - Particle mass determination by gravimetric analysis
ISO 16232-7: Road vehicles - Particle sizing and counting by microscopic analysis
ISO 16232-8: Road vehicles - Cleanliness of components of fluid circuits - Part 8: Particle nature determination by microscopic analysis
ISO 16232-9: Road vehicles - Particle sizing and counting by automatic light extinction particle counter
ISO 16232-10: Road vehicles - Part 10: Expression of results
MAN M 3652: Technical cleanliness of fluid lines for use in commercial vehicles
SAE J400: Test for Chip Resistance of Surface Coatings
DIN EN ISO 2178: Non-magnetic coatings on magnetic base metals - Measurement of layer thickness
WN0004: Component / System Cleanliness
DIN 50018: Testing in condensed water alternating climate with sulfur dioxide-containing atmosphere
DIN 53504: Testing of rubber and elastomers - Determination of tensile strength, tensile strength, elongation at break and tensile stress values
DIN 53508: Testing of rubber and elastomers - Artificial aging
DIN 53512: Testing of rubber and elastomers - Determination of rebound resilience (Schob pendulum)
DIN EN 438-2 High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (laminates) - Part 2: Determination of properties
DIN EN 660-2: Resilient floor coverings - Determination of wear behavior - Part 2: Frick-Taber test
DIN EN 1067: Adhesives - Examination and preparation of samples for testing
DIN EN 1518: Non-destructive testing - Leak test - Characterization of mass spectrometric leak detectors
DIN EN 13523-6: Strip-coated metals - Test methods - Part 6: Adhesive strength after impressions (cupping test)
DIN EN 15042-2 Coating Thickness Measurement and Characterization of Surfaces by Surface Waves - Part 2: Guidelines for Photothermal Coating Thickness Measurement
DIN EN 15184: Products and systems for the protection and repair of concrete structures - Test methods - Tensile strength between coated steel and concrete
DIN EN 60068-2-7: Environmental testing - Part 2: Tests Ga and Guidelines; Uniform acceleration
DIN EN 60068-2-10: Environmental influences - Part 2-10: Test methods - Test J and Guideline: Mold growth
DIN EN 60068-2-11: Environmental tests - Part 2: Tests - Test Ka: salt spray
DIN EN 60068-2-13: Environmental tests - Part 2: Tests - Test group M: Low air pressure
DIN EN 60068-2-17: Environmental testing - Part 2: Tests - Testing Q: Tightness
DIN EN 60068-2-20: Environmental influences - Part 2-20: Tests - Test T: Test method for the solderability and soldering heat resistance of components with lead-out terminals
DIN EN 60068-2-21: Environmental testing - Part 2-21: Tests - Test U: Resistance of connections and integral fasteners
DIN EN 60068-2-30: Environmental influences - Part 2-30: Test method - Test Db: Moist heat, cyclic (12 + 12 hours)
DIN EN 60068-2-40: Environmental testing - Part 2: Tests - Z / AM test: Combined cold / low air pressure test
DIN EN 60068-2-41: Environmental testing - Part 2: Tests - Z / BM: Combined test
DIN EN 60068-2-42: Environmental tests - Part 242: Tests - Test Kc - Sulfur dioxide for contacts and joints
DIN EN 60068-2-43: Environmental tests - Part 243: Tests - Examination Kd: Hydrogen sulfide for contacts and compounds
DIN EN 60068-2-45: Environmental testing - Part 2; Tests - Examination XA and Guide: Dipping in liquid detergents
DIN EN 60068-2-47: Environmental influences - Part 2-47: Test methods - Fastening of test pieces for vibration, shock and similar dynamic tests
DIN EN 60068-2-48: Environmental testing - Part 2-48: Tests - Guidelines for the application of tests
DIN EN 60068-2-61: Environmental testing - Part 2-61: Test method - Z / ABDM test: Order of climatic tests
DIN EN 60068-2-66: Environmental testing - Part 2-66: Test method - Test Cx: Moisture heat, constant (unsaturated pressure steam)
DIN EN 60068-2-67: Environmental testing - Part 2-67: Tests - Examination Cy: Moisture heat, constant, accelerated test, preferably for components
DIN EN 60068-2-68: Environmental testing - Part 2-67: Tests - Test L: Dust and sand
DIN EN 60068-2-70: Environmental testing - Part 2-70: Tests - Examination Xb: Testing of the resistance of marks and inscriptions to abrasion caused by wiping with fingers and hands
DIN EN 60068-2-77: Environmental testing - Part 2-77: Tests - Test 77: Body strength and impact test
DIN EN 60068-2-80: Environmental influences - Part 2-80: Test method - Test method Fi: Mixed-mode vibration test
DIN EN 60068-2-81: Environmental tests - Part 281: Tests - Test egg: shock. Synthesis of the shock response spectrum
DIN EN 60068-2-82: Environmental influences - Part 2-82: Tests - Tx test: Whisker test method for electronic and electrical components
DIN EN 60068-2-83: Environmental testing - Part 2-83: Tests - Test Tf: Solderability testing of surface mount electronics (SMD) using the wetting scale using solder paste
DIN EN ISO 75-2: Plastics - Determination of heat distortion temperature - Part 2: Plastics and hard rubber
DIN EN ISO 291: Plastics - Normal climates for conditioning and testing
DIN EN ISO 306: Plastics - Thermoplastics - Determination of Vicat softening temperature (VST)
DIN EN ISO 527-1: Plastics - Determination of tensile properties - Part 1: General principles
DIN EN ISO 527-2: Plastics - Determination of tensile properties - Part 2: Test conditions for molding and extrusion compounds
DIN EN ISO 527-3: Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets
DIN EN ISO 527-4: Plastics - Determination of tensile properties - Part 4; Test conditions for isotropic and anisotropic fiber reinforced plastic composites
DIN EN ISO 527-5: Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fiber reinforced plastic composites
DIN EN ISO 868: Plastics and hard rubber - Determination of indentation hardness with a durometer (Shore hardness)
DIN EN ISO 1133-1: Plastics - Determination of melt mass flow rate (MFR) and melt volume flow rate (MVR) of thermoplastics - Part 1: General test method
DIN EN ISO 1133-2: Plastics - Determination of melt mass flow rate (MFR) and melt volume flow rate (MVR) of thermoplastics - Part 2: Procedures for materials that are sensitive to a time- or temperature-dependent history and / or humidity
DIN EN ISO 1183-1: Plastics - Methods for determining the density of non-foamed plastics - Part 1: Immersion method, liquid pyknometer method and titration method
DIN EN ISO 1183-2: Plastics - Methods for determining the density of non-foamed plastics - Part 2: Density gradient method
DIN EN ISO 1183-3: Plastics - Determination of the density of non-foamed plastics - Part 3: Gas pyknometer method
DIN EN ISO 1518-1: Paints and varnishes - Determination of scratch resistance - Part 1: Constant load method
DIN EN ISO 1518-2: Paints and varnishes - Determination of scratch resistance - Part 2: Method with continuously increasing load
DIN EN ISO 1519: Paints and varnishes - mandrel bending test (cylindrical mandrel)
DIN EN ISO 1519-1 Plastics piping systems for the discharge of waste water (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Requirements for pipes, fittings and the piping system
DIN EN ISO 1520: Coating materials - Creep test
DIN EN ISO 1522: Paints and varnishes - Pendulum damping test
DIN EN ISO 1524: Paints and varnishes - Determination of grinding fineness (granularity)
DIN EN ISO 2360: Non-conductive coatings on non-magnetic metallic base materials - Measurement of layer thickness - Eddy current method
DIN EN ISO 2431: Paints and varnishes - Determination of flow time with outlet cups
DIN EN ISO 2555: Plastics - Resins in the liquid state, in the form of emulsions or dispersions - Determination of the apparent viscosity by means of a single-jet rotary viscometer
DIN EN ISO 2808: Paints and varnishes - Determination of layer thickness
DIN EN ISO 2811-1: Paints and varnishes - Determination of density - Part 1: Pycnometer method
DIN EN ISO 2811-2: Paints and varnishes - Determination of density - Part 2: Immersion method
DIN EN ISO 2811-3: Paints and varnishes - Determination of density - Part 3: Vibration method
DIN EN ISO 2811-4: Paints and varnishes - Determination of density - Part 4: Pressure cylinder method
DIN EN ISO 2813: Paints and varnishes - Determination of gloss value below 20 , 60 and 85
DIN EN ISO 2884-1: Paints and varnishes - Determination of viscosity using rotational viscometers - Part 1: Cone-plate viscometer at high velocity gradient
DIN EN ISO 2884-2: Paints and varnishes - Determination of viscosity using rotational viscometers -
DIN EN ISO 4288: Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for surface quality assessment
DIN EN ISO 4624: Paints and varnishes - Tear-off test to determine the adhesion
DIN EN ISO 5470-1: Rubber or plastics coated textiles - Determination of abrasion resistance - Part 1: Taber abrasion tester
DIN EN ISO 5470-2: Rubber or plastics coated textiles - Determination of abrasion resistance - Part 2: Martindale abrasion tester
DIN EN ISO 6504-1: Paints and varnishes - Determination of hiding power - Part 1: Kubelka-Munk method for white and light coatings
DIN EN ISO 6504-3: Paints and varnishes - Determination of hiding power - Part 3: Determination of the hiding power of coatings for mineral substrates and concrete
DIN EN ISO 7668: Anodizing of aluminum and aluminum alloys - Measurement of the directional reflectance and specular gloss of anodic oxide coatings at angles of 20 , 45 , 60 or 85
DIN EN ISO 7784-1: Paints and varnishes - Determination of abrasion resistance - Part 1: Procedure with sandpaper-coated wheels and rotating specimen
DIN EN ISO 7784-2: Paints and varnishes - Determination of abrasion resistance - Part 2: Procedure using rubber and rotating friction wheels
DIN EN ISO 7784-3: Paints and varnishes - Determination of abrasion resistance - Part 3: Procedure with sandpaper-coated wheel and reciprocating sample
DIN EN ISO 8501-1: Preparation of steel surfaces prior to the application of coating materials - Visual assessment of surface cleanliness - Part 1: Degree of rust and surface preparation of uncoated steel surfaces and steel surfaces after removal of existing coatings
DIN EN ISO 8501-: Preparation of steel surfaces prior to application of coating materials - Visual assessment of surface cleanliness - Part 2: Surface preparation of coated surfaces after local removal of existing coatings
DIN EN ISO 8501-3: Preparation of steel surfaces prior to the application of coating materials - Visual assessment of surface cleanliness - Part 3: Preparation of welds, edges and other surfaces with surface irregularities
DIN EN ISO 8501-4: Preparation of steel surfaces prior to application of coating materials - Visual assessment of surface cleanliness - Part 4: Initial conditions, preparation grades and degrees of rust in combination with high pressure water washing
DIN EN ISO 8502-2: Preparation of steel surfaces prior to the application of coating materials - Tests for assessing surface cleanliness - Part 2: Laboratory determination of chloride on cleaned surfaces
DIN EN ISO 8502-3: Preparation of steel surfaces prior to the application of coating materials - Tests for assessing surface cleanliness - Part 3: Evaluation of dust on steel surfaces prepared for coating (adhesive tape method)
DIN EN ISO 8502-4: Preparation of steel surfaces prior to the application of coating materials - Surface purity assessment tests - Part 4: Guidance for estimating the likelihood of dew formation before coating
DIN EN ISO 8502-5: Preparation of steel surfaces prior to the application of coating materials - Tests for assessing surface cleanliness - Part 5: Measurement of chlorides on prepared steel surfaces (Method for detection of ions with test tubes)
DIN EN ISO 8502-6: Preparation of steel surfaces prior to the application of coating materials - Tests for evaluating surface cleanliness - Part 6: Dissolution of water-soluble impurities for analysis - Bresle method
DIN EN ISO 8502-9: Preparation of steel surfaces prior to the application of coating materials - Tests for assessing surface cleanliness - Part 9: Field method for the determination of water-soluble salts by conductivity measurement
DIN EN ISO 8502-11: Preparation of steel surfaces prior to the application of coating materials - Tests for assessing surface cleanliness - Part 11: Field method for the determination of water-soluble sulphate by turbidity measurement
DIN EN ISO 8503-1: Preparation of steel surfaces prior to the application of coating materials - Roughness characteristics of blasted steel surfaces - Part 1: Requirements and terms for ISO roughness comparison samples for the evaluation of blasted surfaces
DIN EN ISO 8503-2: Preparation of steel surfaces prior to the application of coating materials - Roughness characteristics of blasted steel surfaces - Part 2: Procedure for roughness testing of blasted steel - Comparison sample method
DIN EN ISO 8503-3: Preparation of steel surfaces prior to the application of coating materials - Roughness characteristics of blasted steel surfaces - Part 3: ISO roughness comparison pattern and roughness calibration method - Microscope method
DIN EN ISO 8503-4: Preparation of steel surfaces prior to application of coating materials - Roughness characteristics of blasted steel surfaces - Part 4: Method of calibrating ISO roughness test patterns and roughness determination - Profile method
DIN EN ISO 8503-5: Preparation of steel surfaces prior to the application of coating materials - Roughness characteristics of blasted steel surfaces - Part 5: Imprint method for determining roughness
DIN EN ISO 9117-1: Paints and varnishes - Drying tests - Part 1: Determination of throughdrying condition and drying time
DIN EN ISO 9117-2: Paints and varnishes - Drying tests - Part 2: Pressure test to determine stackability
DIN EN ISO 9117-3: Paints and varnishes - Drying tests - Part 3: Testing of surface drying with glass beads
DIN EN ISO 9117-4: Paints and varnishes - Drying tests - Part 4: Procedure with a mechanical recorder
DIN EN ISO 9117-5: Paints and varnishes - Drying tests - Part 5: Modified Bandow-Wolff method
DIN EN ISO 9117-6: Paints and varnishes - Drying tests - Part 6: Determination of resistance to impact
DIN EN ISO 11127-1: Preparation of steel surfaces prior to the application of coating materials - Test methods for non-metallic abrasives - Part 1: Sampling
DIN EN ISO 11127-2: Preparation of steel surfaces prior to coating application - Test methods for non-metallic abrasives - Part 2: Determination of particle size distributions
DIN EN ISO 11127-3: Preparation of steel surfaces prior to coating - Test method for non-metallic abrasives - Part 3: Determination of apparent density
DIN EN ISO 1127-4: Preparation of steel surfaces prior to the application of coating materials - Test methods for non-metallic blasting abrasives - Part 4: Estimation of hardness by comparison with glass panes
DIN EN ISO 11127-5: Preparation of steel surfaces prior to the application of coating materials - Test methods for non-metallic blasting abrasives - Part 5: Determination of moisture
DIN EN ISO 11127-6: Preparation of steel surfaces prior to the application of coating materials - Test methods for non-metallic blasting abrasives - Part 6: Determination of water-soluble impurities by measurement of conductivity
DIN EN ISO 11127-7: Preparation of steel surfaces prior to the application of coating materials - Test method for non-metallic blasting abrasives - Part 7: Determination of water-soluble chlorides
DIN EN ISO 11357: Plastics - Differential scanning thermal analysis (DSC) - Part 1: General principles
DIN EN ISO 11357-2: Plastics - Differential scanning thermal analysis (DSC) - Part 2: Determination of glass transition temperature and glass transition step height
DIN EN ISO 11357-3: Plastics - Differential scanning thermal analysis (DSC) - Part 3: Determination of melting and crystallization temperature and enthalpy of fusion and crystallization
DIN EN ISO 11357-4: Plastics - Differential scanning thermal analysis (DSC) - Part 4: Determination of specific heat capacity
DIN EN ISO 11357-5: Plastics - Differential scanning thermal analysis (DSC) - Part 5: Determination of characteristic reaction temperatures and times, reaction enthalpy and conversion
DIN EN ISO 11357-6: Plastics - Differential scanning thermal analysis (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
DIN EN ISO 11357-7: Plastics - Differential scanning thermal analysis (DSC) - Part 7: Determination of crystallization kinetics
DIN EN ISO 11358-1: Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles
DIN EN ISO 11997-1: Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 1: Wet (salt spray) / dry / damp
DIN EN ISO 11997-2: Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt spray) / dry / moisture / UV radiation
DIN EN ISO 11998: Paints and varnishes - Determination of wet abrasion resistance and cleanability of coatings
DIN EN ISO 16276-1: Corrosion protection of steel structures by coating systems - Assessment of the adhesion / cohesion (adhesion) of a coating and criteria for its acceptance - Part 1: Tear-off test
DIN EN ISO 16276-2: Corrosion protection of steel structures by coating systems - Assessment of the adhesion / cohesion (adhesion) of a coating and criteria for its acceptance - Part 2: Crosshatch and cross cut test
DIN EN ISO 17872: Paints and varnishes - Guidelines for applying scratches through a coating on metal plates for corrosion testing
DIN ISO 34-1: Elastomers or thermoplastic elastomers - Determination of tear propagation resistance - Part 1: Striped, angular and curved specimens
DIN ISO 48: Elastomers or thermoplastic elastomers - Determination of hardness (hardness between 10 IRHD and 100 IRHD)
DIN ISO 815-1: Elastomers or thermoplastic elastomers - Determination of compression set - Part 1: At ambient or elevated temperatures
DIN ISO 868: Plastics and hard rubber - Determination of indentation hardness with a durometer (Shore hardness)
DIN ISO 1431-1: Elastomers or thermoplastic elastomers - Resistance to ozone cracking - Part 1: Static and dynamic strain test
DIN ISO 1431-3: Elastomere oder thermoplastische Elastomere - Widerstand gegen Ozonrissbildung - Teil 3: Referenz- und alternative Verfahren zur Bestimmung der Ozonkonzentration in Laborprüfkammern
DIN ISO 1652: Kautschuk-Latex - Bestimmung der Viskosität nach dem Brookfield-Verfahren
DIN ISO 1817: Elastomere oder thermoplastische Elastomere - Bestimmung des Verhaltens gegenüber Flüssigkeiten
DIN ISO 2115: Kunststoffe - Polymerdispersionen - Bestimmung der Weißpunkt-Temperatur und Mindest-Filmbildetemperatur
DIN ISO 2285: Elastomere oder thermoplastische Elastomere - Bestimmung des Zugverformungsrestes unter konstanter Dehnung und des Zugverformungsrestes, der Dehnung und des Fließens unter konstanter Zugbelastung
DIN ISO 3310-1: Analysensiebe - Technische Anforderungen und Prüfung - Teil 1: Analysensiebe mit Metalldrahtgewebe
DIN ISO 3310-2: Analysensiebe - Technische Anforderungen und Prüfung - Teil 2: Analysensiebe mit Lochblechen
DIN ISO 3310-3: Analysensiebe - Technische Anforderungen und Prüfung - Teil 3: Analysensiebe mit elektrogeformten Siebfolien
DIN ISO 3384-1: Elastomere oder thermoplastische Elastomere - Bestimmung der Spannungsrelaxation unter Druck - Teil 1: Prüfung bei konstanter Temperatur
DIN ISO 3601-3: Fluidtechnik - O-Ringe - Teil 3: Form- und Oberflächenabweichungen
DIN ISO 7619-1: Elastomere oder thermoplastische Elastomere - Bestimmung der Eindringhärte - Teil 1: Durometer-Verfahren (Shore-Härte)
DIN ISO 7991: Glas - Bestimmung des mittleren thermischen - Längenausdehnungskoeffizienten
DIN 53109 : Prüfung von Papier und Pappe - Bestimmung des Abriebs nach dem Reibradverfahren
DIN 53159 : Beschichtungsstoffe - Bestimmung des Kreidungsgrades von Beschichtungen nach Kempf
DIN 53435 : Prüfung von Kunststoffen - Biegeversuch und Schlagbiegeversuch an Dynstat-Probekörpern
DIN 53497 : Prüfung von Kunststoffen - Warmlagerungsversuch an Formteilen aus thermoplastischen Formmassen, ohne äußere mechanische Beanspruchung
DIN 55670: Paints and varnishes - Testing of coatings on pores and cracks with high voltage
DIN 55900-1: Coatings for space heaters - Part 1: Terms, requirements and testing for base coats and industrially produced base coats
DIN 55900-2: Coatings for space heaters - Part 2: Terms, requirements and testing for topcoats and topcoats industrially produced
DIN 55997: Solvents for coating materials - deionised water
DIN 75201: Determination of the fogging behavior of automotive interior materials
DIN EN 1183: Materials and articles - in contact with foodstuffs - Test methods for thermal shock and thermal shock resistance
DIN EN 1516: Sports floors - Determination of the impression behavior
DIN EN 14241-1: Exhaust systems - Material requirements and tests for elastomeric seals and sealing materials - Part 1: Seals for use in inner tubes
DIN EN 23270: Paints, paints and their raw materials - Temperature and humidity for conditioning and testing
DIN EN ISO 1183-1: Plastics - Methods for determining the density of non-foamed plastics - Part 1: Immersion method, liquid pyknometer method and titration method
DIN EN ISO 1183-2: Plastics - Methods for determining the density of non-foamed plastics - Part 2: Density gradient method
DIN EN ISO 1183-3: Plastics - Determination of the density of non-foamed plastics Part 3: Gas pyknometer method
DIN EN ISO 1513: Paints and varnishes - Testing and preparation of samples
DIN EN ISO 1514: Paints and varnishes - Standard sample plates
DIN EN ISO 1518-1: Paints and varnishes - Determination of scratch resistance - Part 1: Constant load method
DIN EN ISO 1518-2: Paints and varnishes - Determination of scratch resistance - Part 2: Method with continuously increasing load
DIN EN ISO 1523: Determination of flash point - Closed-cup equilibrium method
DIN EN ISO 2810: Paints and varnishes - Weathering of coatings - Weathering and evaluation
DIN EN ISO 2815: Paints and varnishes - impression test according to Buchholz
DIN EN ISO 3219: Plastics - Polymers / Resins in liquid, emulsified or dispersed state - Determination of viscosity with a rotational viscometer at a defined velocity gradient
DIN EN ISO 3231: Paints and varnishes - Determination of resistance to moist sulfur dioxide containing atmospheres
DIN EN ISO 3248: Paints and varnishes - Determination of the effect of heat
DIN EN ISO 3668: Paints and varnishes - Visual comparison of the color of coatings
DIN EN ISO 4623-1: Paints and varnishes - Determination of resistance to filiform corrosion - Part 1: Steel as substrate
DIN EN ISO 9038: Determination of burnability of liquids
DIN EN ISO 9514: Paints and varnishes - Determination of working time of multi-component coating systems - Preparation and conditioning of samples and guide for testing
DIN EN ISO 12944-2: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 2: Classification of environmental conditions
DIN EN ISO 12944-6: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 6: Laboratory tests for evaluation of coating systems
DIN EN ISO 12944-7: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 7: Design and supervision of coating operations
DIN EN ISO 12944-8: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 8: Development of specifications for initial protection and repair
DIN EN ISO 13803: Paints and varnishes - Determination of the haze of coatings at 20
DIN EN ISO 13900: Steel - Determination of boron content - Curcumin method. Photometric determination after distillation
DIN EN ISO 13900-1: Pigments and fillers - Dispersing process and assessment of dispersibility in plastics - Part 1: General information
DIN EN ISO 13900-2: Pigments and fillers - Dispersing process and evaluation of dispersibility in plastics - Part 2: Determination of coloristic properties and dispersing hardness in plasticisers
DIN EN ISO 13900-4: Pigments and extenders - Dispersing process and assessment of dispersibility in plastics - Part 4: Determination of coloristic properties and dispersing hardness of white pigments in polyethylene in the rolling test
DIN EN ISO 13900-5: Pigments and extenders - Dispersion method and assessment of dispersibility in plastics - Part 5: Determination by pressure filter test
DIN EN ISO 13900-6: Pigments and extenders - Dispersion method and assessment of dispersibility in plastics - Part 6: Determination by film test
DIN EN ISO 3219: Plastics - Polymers / Resins in liquid, emulsified or dispersed state - Determination of viscosity with a rotational viscometer at a defined velocity gradient
DIN EN ISO 3231: Paints and varnishes - Determination of resistance to moist sulfur dioxide containing atmospheres
DIN EN ISO 3248: Paints and varnishes - Determination of the effect of heat
DIN EN ISO 3668: Paints and varnishes - Visual comparison of the color of coatings
DIN EN ISO 4623-1: Paints and varnishes - Determination of resistance to filiform corrosion - Part 1: Steel as substrate
DIN EN ISO 9038: Determination of burnability of liquids
DIN EN ISO 9514: Paints and varnishes - Determination of working time of multi-component coating systems - Preparation and conditioning of samples and guide for testing
DIN EN ISO 12944-2: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 2: Classification of environmental conditions
DIN EN ISO 12944-6: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 6: Laboratory tests for evaluation of coating systems
DIN EN ISO 12944-7: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 7: Design and supervision of coating operations
DIN EN ISO 12944-8: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 8: Development of specifications for initial protection and repair
DIN EN ISO 13803: Paints and varnishes - Determination of the haze of coatings at 20
DIN EN ISO 13900: Steel - Determination of boron content - Curcumin method. Photometric determination after distillation
DIN EN ISO 13900-1: Pigments and fillers - Dispersing process and assessment of dispersibility in plastics - Part 1: General information
DIN EN ISO 13900-2: Pigments and fillers - Dispersing process and evaluation of dispersibility in plastics - Part 2: Determination of coloristic properties and dispersing hardness in plasticisers
DIN EN ISO 13900-4: Pigments and extenders - Dispersing process and assessment of dispersibility in plastics - Part 4: Determination of coloristic properties and dispersing hardness of white pigments in polyethylene in the rolling test
DIN EN ISO 13900-5: Pigments and extenders - Dispersion method and assessment of dispersibility in plastics - Part 5: Determination by pressure filter test
DIN EN ISO 13900-6: Pigments and extenders - Dispersion method and assessment of dispersibility in plastics - Part 6: Determination by film test
DIN EN ISO 3219: Plastics - Polymers / Resins in liquid, emulsified or dispersed state - Determination of viscosity with a rotational viscometer at a defined velocity gradient
DIN EN ISO 3231: Paints and varnishes - Determination of resistance to moist sulfur dioxide containing atmospheres
DIN EN ISO 3248: Paints and varnishes - Determination of the effect of heat
DIN EN ISO 3668: Paints and varnishes - Visual comparison of the color of coatings
DIN EN ISO 4623-1: Paints and varnishes - Determination of resistance to filiform corrosion - Part 1: Steel as substrate
DIN EN ISO 9038: Determination of burnability of liquids
DIN EN ISO 9514: Paints and varnishes - Determination of working time of multi-component coating systems - Preparation and conditioning of samples and guide for testing
DIN EN ISO 12944-2: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 2: Classification of environmental conditions
DIN EN ISO 12944-6: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 6: Laboratory tests for evaluation of coating systems
DIN EN ISO 12944-7: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 7: Design and supervision of coating operations
DIN EN ISO 12944-8: Paints and varnishes - Corrosion protection of steel structures by coating systems - Part 8: Development of specifications for initial protection and repair
DIN EN ISO 13803: Paints and varnishes - Determination of the haze of coatings at 20
DIN EN ISO 13900: Steel - Determination of boron content - Curcumin method. Photometric determination after distillation
DIN EN ISO 13900-1: Pigments and fillers - Dispersing process and assessment of dispersibility in plastics - Part 1: General information
DIN EN ISO 13900-2: Pigments and fillers - Dispersing process and evaluation of dispersibility in plastics - Part 2: Determination of coloristic properties and dispersing hardness in plasticisers
DIN EN ISO 13900-4: Pigments and extenders - Dispersing process and assessment of dispersibility in plastics - Part 4: Determination of coloristic properties and dispersing hardness of white pigments in polyethylene in the rolling test
DIN EN ISO 13900-5: Pigments and extenders - Dispersion method and assessment of dispersibility in plastics - Part 5: Determination by pressure filter test
DIN EN ISO 13900-6: Pigments and extenders - Dispersion method and assessment of dispersibility in plastics - Part 6: Determination by film test
DIN EN ISO 15528: Paints and varnishes for coating materials - Sampling
DIN EN ISO 16474-1: Paints and varnishes - Artificial irradiation or weathering in equipment - Part 1: General instructions
DIN EN ISO 16474-2: Paints and varnishes - Artificial irradiation or weathering in equipment - Part 2: Xenon arc lamps
DIN EN ISO 16474-3: Paints and varnishes - Artificial irradiation or weathering in equipment - Part 3: UV fluorescent lamps
DIN EN ISO 21227-1: Paints and varnishes - Assessment of coating damage by means of digital image processing - Part 1: General instructions
DIN EN ISO 22088-1: Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 1: General instructions
DIN EN ISO 22088-2: Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 2: Creep rupture test
DIN EN ISO 22088-3: Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 3: Bending strip method
DIN EN ISO 22088-4: Plastics - Determination of environmental stress cracking resistance (ESC) - Part 4: Ball or pin insertion techniques
DIN EN ISO 22088-5: Plastics - Determination of environmental stress cracking resistance (ESC) - Part 5: Constant tension deflection method
EN ISO 22088-6: Plastics - Determination of environmental stress cracking resistance (ESC) - Part 6: Slow strain rate method
JDM F17: Enterprise Specification for Paint Performance
JDM F14: Enterprise Specification for Performance of High Temperature Paints
DIN EN ISO 4042: Fasteners - Galvanic coatings
JDM F15: Specification for Electroplated Coatings for Fasteners
JDM F10: Specification for Phosphate / Oil Protective Coatings
JDM F11: Specification for Performance Paints on John Deere Parts and Products
JDM F12: Specification for Performance of Primer Paints on John Deere Parts and Products
JDM F13: Specification for Non-Electrolytically Applied Zinc Flake Coatings
JDM F21: Fasteners, Hydraulic Connectors, Hose Fittings and Tube Assemblies - Specification for Zinc-Nickel Electroplated Coating Requirements
JDM F22: Specification for Mechanical Zinc Coating
JDM F23: Specification for Electroplated Zinc Coating on Non-Fastener Parts
JDM H4: Specification for O-Ring Materials and Properties
JDM J20: Specification for Anti-Brake Chatter Transmission / Hydraulic Fluids
JDQ 1: Paints - Determination of Paint Hardness - Pencil Test
JDQ 17: Paints - Evaluation of Paint Film Adhesion - Cross-Cut Test
JDQ 53.3: Environmental Design and Testing of Electronic / Electrical Components and Assemblies
JDQ 114: Evaluation of Color Differences - Instrumental Test Methods
JDQ 138: Tests for Chemical Resistance of Paint Films
JDQ 142: Tests for Chemical Resistance of Paint Films by Spot Exposure Method
JDQ 145: Tests for Wet Adhesion of Paint Films by Cross-Cut Method
JDQ 148: Tests for Cyclic Temperature Resistance of High Temperature Coatings
JDQ 149: High Temperature Paints and Coatings - Evaluation of Thermal Shock Resistance
JDQ 159: Cyclic Corrosion Test for Corrosion Resistance of Paint Films
JDQ 163: Corrosion Resistance of Coatings - Simulated Corrosive Atmospheric Breakdown Test
JDQ 201: Testing Electronic and Electrical Devices - Environmental and Mechanical Loads
JDQ 117: Specification for Electroplated Zinc and Zinc Cobalt Coatings
JDS-G169: Classification systems for the purity of liquids, components and assemblies
JDQ 115: Salt Spray Test for Corrosion Resistance of Paint Films
LaN 930: Anti-corrosion coatings - classification and designation
LaN 975: Tests for Primer and Topcoats PAINTING: TESTS OF PRIMER AND TOP COAT
JDV 30: Paint Process Prerequisites for Meeting JDM F17 and JDM F20 Performance Requirements
JDM F9: John Deere Colors
JDQ 12: Paints and Polymers - Determination of Specular Gloss at 20 and 60
ASTM D4176: Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels
ASTM E96: Standard Test Methods for Water Vapor Transmission of Materials
BMW PR 292: Attachments underbody
BMW AA-0079: Determination of stone chip resistance by means of multi-layer
DBL 5562: Components Manufactured from Thermoplastic Elastomers
BMW GS 90010-1: Surface protection types for metallic materials
AWN 060501: Amazone factory standard - purity requirements for hydraulic components and systems
M 3652: MAN Truck & Bus AG - Technical cleanliness of fluid lines for use in commercial vehicles
WN0004: Steyr Component / System Cleanliness
NES M0141: Nissan Coating of Synthetic resin
FORD CEPT 00.00-L-467: Cyclic corrosion test- Global Laboratory Accelerated Cyclic Corrosion Test
PV 3983: VW - Media resistance of plastics and thermoplastic elastomers in combination with mechanical stresses
TL 52712: VW - Thermoplastic Lines with Low Material Dissolution for Gasoline
VW 50002: Test media Material compatibility
VW 96393: Elastomer resistance to blow-by gases
PV 3936: Polymer materials Resistance to components of crankcase gases
PV 3983: Plastics and thermoplastic elastomers Testing of media resistance in combination with mechanical
VDA 233-102: Cyclic corrosion test
PV 1401: Lubricating oils - Testing of corrosion protection behavior
PV 3929: Non-Metallic Materials Weathering in Dry-Hot Climate (Kalahari)
PV 3930: Non-Metallic Materials Weathering in Humid and Warm Climate (Arizona)
PV 1209: Condensers, water and intercooler made of Al alloys Corrosion test (climate corrosion change test)
PV 1200: Alternating climate test -40 C - + 80 C
PV 1210: Body and attachments Corrosion test
PV 3307: Elastomer components Plastic and elastic deformability
TL 244-12: Zinc / nickel alloy coatings Surface protection requirements
VW 96393: Elastomeric resistance to blow-by gases
VW 2.8.1: Elastomeric material requirements and tests
TL 226: Paintworks on Materials Used in the Vehicle Interior Trim
TL 256: Powder Paint on Metal Surfaces Surface Protection Requirements
PV 3952: Plastic Interior Components Testing of Scratch Resistance
PV 1303: Non-Metallic Materials Exposure Test of Passenger Compartment Components
DIN 51360-2: Determination of the corrosion protection properties of water-mixed cooling lubricants
DIN 51368: Determination of the portion of water-mixed cooling lubricants that can be separated with acidic acid
DIN 51777-1: Testing of mineral oil hydrocarbons and solvents - Determination of water content according to Karl Fischer
DIN 51777-2: Testing of mineral oil hydrocarbons and solvents-Determination of the water content
DIN 53160-1: Determination of the color content of articles of daily use - Part 1: Testing with saliva simulant
DIN 53160-2: Determination of the color content of articles of daily use - Part 2: Testing with welding simulant
DIN EN ISO 1518-1: Paints and varnishes - Determination of scratch resistance - Part 1: Constant load method
DIN EN ISO 1518-2: Paints and varnishes - Determination of scratch resistance - Part 2: Method with continuously increasing load
DIN EN ISO 1520: Coating materials - Creep test
DIN EN ISO 1522: Paints and varnishes - Pendulum damping test
DIN EN ISO 2360: Non-conductive coatings on non-magnetic metallic base materials - Measurement of layer thickness - Eddy current method
DIN EN ISO 2592: Petroleum products and related products - Determination of flame and focus - Cleveland open-cup method
DIN EN ISO 2812: Paints and varnishes - Determination of resistance to liquids - Part 5: Graded furnace method
DIN EN ISO 3104: Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and dynamic viscosity calculation
DIN EN ISO 3675: Crude oils and liquid petroleum products - Determination of density in the laboratory
DIN EN ISO 4042: Fasteners - Galvanic coatings
DIN EN ISO 4892-1: Plastics - Artificial irradiation or weathering in equipment - Part 1: General instructions
DIN EN ISO 4892-2: Plastics - Artificial irradiation or weathering in equipment - Part 2: Xenon arc lamps
DIN EN ISO 4892-3: Plastics - Artificial irradiation or weathering in equipment - Part 3: UV fluorescent lamps
DIN EN ISO 6988: Metallic and other inorganic coatings Testing with sulfur dioxide under general humidity condensation
DIN EN ISO 9227: Corrosion tests in artificial atmospheres - salt spray tests
DIN EN ISO 11664-1: Colorimetry - Part 1: CIE colorimetric standard observers
DIN EN ISO 11664-2: Colorimetry - Part 2: CIE standard illuminants
DIN EN ISO 11664-3: Colorimetry - Part 3: CIE color values
DIN EN ISO 11664-4: Colorimetry - Part 4: CIE 1976 L * a * b * Color space
DIN EN ISO 11664-5: Colorimetry - Part 5: CIE 1976 L * u * v * color space and equidistant u ', v' color chart
DIN EN ISO 11664-6: Colorimetry - Part 6: CIEDE2000 Color distance formula
DIN EN ISO 12937: Petroleum products Determination of water content Coulometric titration according to Karl Fischer
DIN EN ISO 15184: Paints and varnishes - Determination of hardness of coatings by testing with pencils
DIN EN ISO 20567-1: Paints and varnishes - Testing of stone chip resistance of coatings - Part 1: Multi-layer test
DIN EN ISO 20567-2: Paints and varnishes - Testing of stone chip resistance of coatings - Part 2: Single impact test with guided impact body
DIN EN ISO 20567-3: Paints and varnishes - Testing the stone chip resistance of coatings - Part 3: Single impact test with free-flowing impactor
DIN ISO 48: Elastomers or thermoplastic elastomers - Determination of hardness (hardness between 10 IRHD and 100 IRHD)
DIN ISO 2909: Petroleum products Calculation of the viscosity index from the kinematic viscosity
DIN ISO 3016: Petroleum products and related products of natural or synthetic origin - Determination of pour point
DIN ISO 7619-1: Elastomers or thermoplastic elastomers - Determination of penetration hardness - Part 1: Durometer method (Shore hardness)
DIN ISO 7619-2: Elastomers or thermoplastic elastomers - Determination of penetration hardness - Part 2: IRHD pocket device method
DIN ISO 1817: Elastomers - Determination of the behavior towards liquids
ISO 1431-1: Elastomers or thermoplastic elastomers - Resistance to ozone cracking - Part 1: Static and dynamic strain test
ISO 1431-3: Elastomers or thermoplastic elastomers - Resistance to ozone cracking - Part 3: Reference and alternative methods for the determination of ozone concentration in laboratory test chambers
ISO 1817: Rubber, vulcanized - Determination often he effect of liquids
DIN 50018: Testing in condensed water alternating climate with sulfur dioxide-containing
ISO 4405: Hydraulic fluid power - Determination of particulate contamination by the gravimetric method
SAE J2334: Laboratory Cyclic Corrosion Test
UL 94: Fire classification test for plastic
VDMA 2364: Testing for paint wetting impurities (LABS conformity) -Testing for paint wetting substances (LABS conformity)
DIN EN ISO 17025: General requirements for the competence of testing and calibration laboratories
AGCO: Corporate Standards Global Engineering Specification
CATERPILLAR: Corporate Product & Process Specification
CNH MAT0103-New Holland and Case Material Specifications
VW 80200-2: Qualification of bodywork components
- CNH-ENS0103 rev C: Component Cleanliness and Acceptance Criteria
- TL 52711: Stone chip test
- Liebherr works standard TLV 23028: Technical cleanliness / Component cleanliness / Residual dirt analysis
- Daimler VAM00328: Technical cleanliness
- Borg Warner Turbo Systems BWS 42001: Component cleanliness
- Behr GN AR.01117: Technical cleanliness
- Audi PV 3336: Component cleanliness
- Bosch PV 1 279 921 533: Technical cleanliness
- BMW QV 11 111: Technical cleanliness, component cleanliness
- Continental GQR 10098907: Technical cleanliness
- Deutz PV 01620033: Component cleanliness
- Fiat FPI.MAN050: Residual dirt analysis, component cleanliness
- GIMA GSP 015, MAGNA POWERTRAIN S40 029, Mercedes Benz DBL 4953: Component cleanliness, technical cleanliness
- Porsche PTL 14045, SAE J2045, Schaeffler Technologies S 252001-2, Seat S.A. PV 3336: Technical Cleanliness
- Siemens SN 52820, Skoda Auto a.s. PV 3336, Thomas WN 0135: Technical cleanliness, component cleanliness, residual dirt analysis
- Thyssen Krupp Bilstein Suspension WNB -881 D,Volvo STD 107-0002, VW PV 3336: Technical cleanliness
- ZF Friedrichshafen AG WN 70/13, ZF Lenksysteme ZFLS NS 5-1: component cleanliness
- ZF Sachs AG ZFN 5008-1, Wacker Neuson WN 71/E , CNH-ENS0103- rev C: technical cleanliness
- FIAT 50488: CHIP RESISTANCE TEST FOR PAINTS ENAMELS, PROTECTIVE COATINGSAND RELATED PRODUCTS
- BMW AA-0054: Resistance of surfaces to brush washing systems
- BMW AA-0055: Resistance test of surfaces to chemicals
- BMW AA-0081: Determination of the parting line of multilayer coatings by means of monoimpact testing
- BMW AA-0129: CASS test
- BMW AA-0175: Corrosion short-time test on painted steel substrate
- BMW AA-180: Cross cut test
- BMW AA-0213: Condensation water constant climate test
- BMW AA-0224: Corrosion change test
- BMW AA-0235 and AA-0236: Short weathering xenon test crack resistance
- BMW AA-0264: Multi-impact test with salt water storage
- BMW GS 97045-2: Painted plastic parts
- BMW GS 90010: Surface protection types for metallic materials
- BMW GS 90011: Coating of parts made of metallic materials with organic materials
- BMW QV 41 278: Cathodic dip coatings and paints
- BMW QV 11 111: Technical cleanliness
- BMW AA-0324: Salt spray test
- Nissan JIS K 8145: Copper (II) chloride dihydrate
- JIS K 8150: Sodium chloride
- JIS K 8355: Acetic acid
- NES M 0140: Salt Spray Testing
- VW PV 2005: Resistance to climatic changes
- DIN EN 60068-2-30: Damp heat, cyclic
- DIN EN 60068-2-38: Temperature/humidity, cyclic
- BMW PR 303.5 and 308.2, DBL 5471, PTL 8140: Climate change tests
- IEC 61215: Humidity/cold cycling test
- DIN EN 60068-2-78: Humid heat, constant
- DIN EN 61215: Damp heat test, 85 C 85%rh
- DBL 5471: climate storage
- PTL 8140: Humidity storage
- DIN EN 60068-2-14: Temperature cycling
- IEC 61215: Temperature cycling test
- DIN EN 60068-2-2 or VDE 0468-2-2: Dry heat, constant
- IEC 60945: Dry heat, constant
- DBL 5471: Heat aging
- DBL 9202, PTL 8140: Heat aging
- DIN EN 60068-2-1 or VDE 0468-2-1: Cold, constant
- IEC 60945: cold, constant
- DBL 5471: cold resistance
- PTL 8140: Cold behavior
- DIN 75220: Sun simulation, dry and humid
- BMW PR 306.4, DBL 5471, PTL 8140: Sun simulation
- DIN ISO 9022-9-20: Sun simulation
- MIL-STD-810F or 810G, section 505.4: Sun simulation
- DIN EN 60068-2-52: Salt spray, cyclic
- DIN EN 60068-2-11: Salt spray
- BMW AA-P 224: Condensation water constant climate test
- DIN EN ISO 105-X12: Color fastness against rubbing
- VW PV 390: Abrasion behavior test
- ISO 6247: Foam behavior sequence I, II and III
- DIN EN ISO 60068-2-14: Temperature shock test
- DIN ISO 7619-1: Shore hardness measurement
- DIN ISO 7619-2: IRHD Shore measurement
- BMW PR 292: Stone impact resistance
- DIN 53380-1: Testing of plastics. Determination of gas permeability
- DIN 53380-2: Testing of plastics. Determination of gas permeability. Part 2: Manometric method for measurement on plastic films.
- DIN 53380-3: Testing of plastics. Determination of gas permeability. Part 3: Oxygen-specific carrier gas method for measurement on plastic films and plastic moldings.
- DIN EN 1062-6: Paints and varnishes. Coating materials and coating systems for exterior mineral substrates and concrete. Part 6: Determination of carbon dioxide permeability.
- DIN EN ISO 6179: Elastomers or thermoplastic elastomers - Elastomeric sheeting and elastomeric coated fabrics - Determination of volatile liquid permeability rate (gravimetric method).
- DIN EN ISO 7783-2: Coating materials and coating systems for exterior mineral substrates and concrete. Part 2: Determination and classification of water vapor diffusion current density (permeability).
- DIN EN ISO 6506-1, DIN EN ISO 6507-1, DIN EN ISO 6508-1, DIN EN ISO 2639, DIN EN ISO 2702, DIN 7500: Hardness tests
- DIN ISO 7619-1, DIN EN ISO 868, DIN ISO 48: Hardness testing of plastics
- DIN EN ISO 148-1: Notched bar impact test
- DIN EN ISO 6892-1, DIN EN ISO 898-1, DIN EN ISO 898-2: Tensile tests
- DBL 5416: Parts made of thermoplastics for cladding, housing and functional parts for exterior applications
- DIN EN ISO 7784; EN 13329; NEMA LD 3-2000; EN 438-2; ISO 4586-2; NALFA LF-01; DIN 52 347 ; DIN 53 109; DIN 53 754; DIN 53 799; DIN 68 861-2; DIN EN 438-2; ISO 3444 ; ISO 3537 ; ISO 4586-2 ; ISO 5470 ; ASTM C 501; ASTM D 1044; ASTM D 3389; ASTM D 3884; ASTM D 406; ASTM D 4158-82; ASTM F 362; ASTM F 510 : Taber Abraser - Determination of abrasion resistance
- IVECO 15-6023: Rockfall test with gravel
- BSH test specification 5600 0000185271, section 1: Abrasion test (Taber test)
- DBL 7399: Stone impact test
- VDMA 24364 - LABS Paint wetting impairment substances
- PV 3.10.7: LABS paint wetting disturbing substances
- PV 3974: Determination of the writing resistance of spray-finished grained surfaces in vehicle interiors
- PV 3952: Testing of scratch resistance
- BOSCH N42AP 226: Corrosion change test
- Nissan CCT1: Corrosion change test
- DIN 55635: Coating materials - Cyclic corrosion test of coating systems on materials and components in automotive engineering
- VDA 233-102: Climatic change test
- DIN ISO 3537: Taber Abraser
- ISO 9211-4: Tesa test
- DIN 55656: Scratch test with hardness test rod
- DIN 53482: Test of behavior against liquids, vapors, gases and solids
- DIN EN ISO 9142: Damp heat cycle
- VDA 621-427: Stone impact test at 2 bar, 2x500 g , chilled cast iron granules
- VW 96435: Testing for contamination - determination of residual particle quantities Lines / hoses / pipes
- ISO 14993: Cyclic corrosion test CCT
- ISO 22479: The standards ISO 6988 and DIN 50 018 together. ISO 6988 previously only a gas load 0.2 S, new ISO 22479 now also again the loads 1.0 S and 2.0 S from DIN 50 018.
- DBL 5562: Components Manufactured from Thermoplastic Elastomers
- VDA 233-102: Cyclic corrosion testing of materials and components in automotive construction
- DIN EN ISO 11997: Coating materials - Determination of resistance to cyclic corrosion conditions
- SAE J2334: Laboratory Cyclic Corrosion Test
- VOLVO STD 1024,7132: Stone chip resistance
- DIN EN 60529: Types of protection
- EN 455: Medical gloves for single use
- LV 124: Electrical and electronic components in passenger cars up to 3.5t General requirements, test conditions and tests Part 2: Environmental requirements
- Paints and varnishes - Testing of resistance to stone impact of coatings - Part 2: Single impact test with guided impactor
- BMW AA-0081: Determination of the parting line of multi-layer coatings by means of mono impact test
- DTRF 150602 - ALSTOM TECHNICAL SPECIFICATION CONSTRUCTION OF RAILWAY ROLLING STOCK
- ISO 15003: Chip resistance - Stone impact test
- LP.7M061: Thermal shock according to FCA
- VW PV 1213: Stone chip resistance test
- BMW GS 95024: Stone chip resistance
- DIN ISO 815-1, ASTM D395 and DIN 53517: Elastomers or thermoplastic elastomers - Determination of compression set - Part 1: At ambient or elevated temperatures
-DIN EN 438-2 und ISO 4586-2: Dekorative Hochdruck-Schichtpressstoffplatten (HPL) Platten auf Basis härtbarer Harze (Schichtpressstoffe) Teil 2: Bestimmung der Eigenschaften
-ASTM D2583: Barcol Härte
M 3018: Korrosionsschutz und Beschichtungssysteme für Kaufteile, LKW und Bus
DIN 55635: Zyklische Korrosionsprüfung
DIN EN ISO 3248: Wärmealterung
DIN ISO 4649: Elastomere oder thermoplastische Elastomere Bestimmung des Abriebwiderstandes mit einem Gerät mit rotierender Zylindertrommel
GMW 15487: Sand abrasion test - Falling Sand Test
JIS Z 2371: Salzsprühnebelprüfung - Methods of neutral salt spray testing
Asbest: Qulitative und Quantitative Analyse von Asbest mittels REM-EDX
DBL 7381: Organische Beschichtung für metallische Teile an der Außen- und Unterseite des Fahrzeugs und im Motorraum
DIN 55635: Zyklische Korrosionsprüfung von Beschichtungssystemen auf Werkstoffen und Bauteilen im Automobilbau
DIN EN ISO 3651-1: Ermittlung der Beständigkeit nichtrostender Stähle gegen interkristalline Korrosion - Korrosionsversuch in Salpetersäure durch Messung des Massenverlustes (Huey-Test)
DIN EN ISO 3651-2: Ermittlung der Beständigkeit nichtrostender Stähle gegen interkristalline Korrosion - Korrosionsversuch in schwefelsäurehaltigen Medien
DIN 50914: Prüfung nichtrostender Stähle auf Beständigkeit gegen interkristalline Korrosion - Kupfersulfat-Schwefelsäure-Verfahren - Strauß-Test
DIN 50908: Prüfung der Beständigkeit von Aluminium-Knetwerkstoffen gegen Spannungsrisskorrosion
DIN 50915: Prüfung von unlegierten und niedriglegierten Stählen auf Beständigkeit gegen interkristalline Spannungsriss-Korrosion in nitrathaltigen Angriffsmitteln
DIN 50916-1: Prüfung von Kupferlegierungen; Spannungsrisskorrosionsversuche mit Ammoniak; Prüfung von Rohren, Stangen und Profilen
DIN 50916-2: Prüfung von Kupferlegierungen; Spannungsrisskorrosionsprüfung mit Ammoniak
ISO 6957: Kupferlegierungen; Prüfung der Beständigkeit gegen Spannungskorrosion mit Ammoniak
ASTM D1149: Ozonprüfung - Ozonrissbildung
ISO 4532: Glas- und Porzellanemaillierungen - Bestimmung der Schlagfestigkeit von emaillierten Gegenständen - Pistolentest
DIN 55996-1: Beschichtungsstoffe - Prüfung der Steinschlagfestigkeit von Beschichtungen - Teil 1: Mehrfachschlagprüfung
VDA 621 - 410: Pendeldämpfung nach König und Persoz
DIN 53 157: Pendeldämpfung nach König und Persoz
ASTM D 4366: Pendeldämpfung nach König und Persoz
Volvo STD 107-0002: Technical cleanliness test
VW 96380: Modifizierter Klimawechseltest
ASTM D968: Standard-Prüfverfahren für die Abriebfestigkeit von organischen Beschichtungen durch fallendes Abrasivmittel- Falling sand abrasion tester
GMW 15487: Falling sand abrasion test
DIN ISO 9211-3: Optik und Photonik - Optische Schichten - Umweltbeständigkeit
DIN-ISO 9022-4: Optik und Photonik - Umweltprüfverfahren - Salzsprühnebel
DIN EN 60068-2-70, BMW GS97034-1, Daimler DBL 7384; IEC 60068-2-70; DIN EN 60068-2-7; ASD-STAN prEN 4860, ISO 15223-1: Handabrieb, Fingernägel und Schuhsole Beständigkeitstest
BMW GS 97034 / GS 97045; Ford WSS-M2P188-A1; EWIMA Spezifikation; Sony Ericsson 45/152 41-FEA 202 8139 Ue: Handabrieb, Fingernägel und Schuchsole Beständigkeitstest
DIN EN 13523-6: Tiefungsprüfung
GS 97034-11: Schuhsole Test
DIN EN ISO 4589-2: Sauerstoffindex
GS 97034--3: Schuhsohlentest
GS 97034--2: Fingernageltest
ISO 34: Elastomere oder thermoplastische Elastomere - Bestimmung des Weiterreißwiderstandes
ISO 178: Biegeversuche
DIN EN ISO 8295: Bestimmung der Reibungskoeffizienten
DIN 53494: Peel test - Schälversuch - Haftfestigkeit
DIN 53375 und ASTM 1894: Bestimmung des Reibungsverhaltens
VOLVO STD 423-0040: Scratch resistance using abrasive paper
MBN 10494 - Teil 1: Allgemeine Anforderungen
MBN 10494 - Teil 2: Prüfung der Lacke im nassen Zustand
MBN 10494 - Teil 3: Verarbeitungstechnische Prüfungen
MBN 10494 - Teil 4: Optische Prüfungen
MBN 10494 - Teil 5: Technisch mechanische Prüfungen
MBN 10494 - Klimatische Prüfungen
MBN 10494 - Teil 7: Beständigkeit gegen Chemikalien, Testgemische und Testkonzentrate
MBN 10494 - Teil 8: Haftung von Klebstoffen auf dem Lack
MBN 10494 - Teil 9: Spezielle Prüfverfahren für Elektrotauchlacke im nassen Zustand
MBN 10494 - Teil 10: Spezielle Prüfverfahren für Elektrotauchlacke im trockenen Zustand
DIN 3415 - Textile Haftverschlüsse, Anforderungen
ISO 2811: Dichtemessung mittels Pyknometers und Druckpyknometers
DIN 53217: Lacke, Farben und Beschichtungsstoffe Bestimmung der Dichte Pyknometer-Verfahren
VW 2.8.1 55 15 2, FIAT 50417, PSA D47 1100, HONDA HES D3200; FORD FLTM BP 101-01; JIS K 6259; NF T46-019; BS 903 A43; GB 7762: Ozonbeständigkeit
BMW AA-0053: Beständigkeit lackierter Oberflächen im Interieur gegenüber Sonnencreme
BMW AA-0055: Beständigkeit von Oberflächen gegenüber Chemikalien
BMW AA-0180: Gitterschnittprüfung
DIN EN 50264-3-1: Ozonprüfung
DIN EN ISO 11124-2: Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen Anforderungen an metallische Strahlmittel Teil 2: Hartguss, kantig (Grit)
DIN EN ISO 11124-1:Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Anforderungen an metallische Strahlmittel - Teil 1: Allgemeine Einleitung und Einteilung
DIN ISO 4532: Bestimmung des Widerstandes emaillierter Gegenstände gegen Schlag - Schlagbolzen-Schlagversuch
ASTM D2794: Schlagzähigkeitversuch
ASTM D4060: Abriebverhalten (Taber Abraser)
ASTM D2240: Filmhärte
ASTM D4541: Abreißversuch zur Bestimmung der Haftfestigkeit
ISO 22479: Korrosion von Metallen und Legierungen - Prüfung mit Schwefeldioxid in feuchter Atmosphäre
PTL 5580: Lackierung auf Kunststoffaußenteilen und Faserverbundkunststoffen
VW 96457: Lackierung auf Kunststoffaußenteilen und Faserverbundkunststoffen
MAN M 3171: Steinschlagprüfung
DIN EN ISO 1463: Schichtidickenmessung mikroskopisch
PSA D42 1235: Impact strength (falling-weight method)
PSA B21 7120 6.3.1: Stone impact resistance test
DIN EN ISO 11998: Bestimmung der Nassabriebbeständigkeit und der Reinigungsfähigkeit
ASTM D 2486: Bestimmung der Nassabriebbeständigkeit und der Reinigungsfähigkeit
ASTM D 4213: Bestimmung der Nassabriebbeständigkeit und der Reinigungsfähigkeit
ASTM D 4828: Bestimmung der Nassabriebbeständigkeit und der Reinigungsfähigkeit
ASTM D 3450: Bestimmung der Nassabriebbeständigkeit und der Reinigungsfähigkeit
DIN EN ISO 16925: Druckwasserstrahlprüfung
PV 1503: Druckwasserstrahlprüfung
SAE J959: Korrosionsschutzmittel, Korrosionsschutz für den Fahrzeugunterboden
NES M0158: Zyklische Korrosionsprüfung
Nissan CCT I: Zyklische Korrosionsprüfung
DIN 53516: Abriebtest = DIN ISO 4649
PF.90331: QUICK CONNECTORS FOR ENGINE
FORD TM 00.00-L-467: Zyklische Korrosionsprüfung
DIN EN ISO 8251: Abriebtest
AA-0203 - Hydrolysetest
AA-0213 - Kondenswasserkonstantklimatest
AA-0026 - Alterungsbeständikeit
AA-0180 - Gitterschnittprüfung
AA-0053 - Beständikeit gegenüber Sonnencreme
ECE-R 124: Prüfungen-Gutachten
DIN EN ISO 12947-1: Bestimmung der Scheuerbeständigkeit von textilen Flächengebilden mit dem Martindale-Verfahren
DIN EN ISO 12945-2: Bestimmung der Neigung von textilen Flächengebilden zur Pillbildung, Flusenbildung oder Verfilzung auf der Oberfläche - Teil 2: Modifiziertes Martindale-Verfahren
PV 1507: Oberfläche von Schlüsselemblemen
ISO 6945: Abriebbeständigkeit
DIN EN ISO 12947-2: Abriebwiderstand - Schuerbeständigkeit
DIN EN ISO 12947: Martindale Verfahren
DIN 30643: Abriebtest
PV 3305: Prüfung der Ozonbeständigkeit und der bleibenden Verformung
SAE J1959: SCAB Test
ISO 14993: Korrosion von Metallen und Legierungen - Beschleunigte Korrosionsprüfung einschließlich zyklischer Beanspruchung durch Salzsprühnebel, "trockenen" und "feuchten" Bedingungen
DIN EN 933-1: Prüfverfahren für geometrische Eigenschaften von Gesteinskörnungen - Teil 1: Bestimmung der Korngrößenverteilung Siebverfahren
ISO 2591-1: Verfahren unter Verwendung von Prüfsieben aus Siebgewebe und Siebblech
PV 8220: Bauteilsauberkeitstest
Tesla TM-5001: Material Spezifikationen für Kataphorese-Elektrolack
CS.00056: Enviromental specifications for electric components
DIN EN ISO 2247: Prüfung mit Schwefeldioxid in feuchter Atmosphäre - Kesternichtest
DIN 50018: Prüfung mit Schwefeldioxid in feuchter Atmosphäre
DIN EN ISO 6988: Prüfung mit Schwefeldioxid in feuchter Atmosphäre
DIN EN ISO 10289: Verfahren zur Korrosionsprüfung von metallischen und anderen anorganischen Überzügen auf metallischen Grundwerkstoffen
MBN 15306-5: Prüfverfahren für Werkstoffsysteme und Komponenten - Teil 5: Sonstige Prüfungen
DBL 8465: Galvanisierte Teile aus Kunststoffen mit metallischen Überzügen und Zusatzbeschichtungen
MBN 10494-5: Lacktechnische Prüfmethoden Teil 5: Technisch-mechanische Prüfungen
TL 256: Pulverlackierung auf Metalloberflächen
DIN ISO 4532: Schlagprüfung nach Wegner

Standards

NonaChem GmbH
Wallstadter Str. 59
D-68526 Ladenburg
GERMANY

E-Mail: info@nonachem.com